Use of egress pushbuttons may not be legal. Single action exit may be required. Always obtain proper permits andapprovals in writing before installing equipment. Notice: This equipment has been tested and found to comply with the limits for a Class A digitaldevice, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonableprotection against harmful interference when the equipment is operated in a commercial environ-ment. This equipment generates, uses, and can radiate radio frequency energy and, if not installedand used in accordance with the instruction manual, may cause harmful interference to radiocommunications.
Operation of this equipment in a residential area is likely to cause harmfulinterference in which case the user will be required to correct the interference at his own expense. Notice: This document and the data herein shall not be duplicated, used or disclosed to others forprocurement or manufacturing, except as authorized with the written permission of NorthernComputers, Inc. The information contained within this document or within the product itself isconsidered the exclusive property and trade secrets of Northern Computers, Inc.
All information inthis document or within the software product itself is protected by the copyright laws of the UnitedStates. Notice: Any use of this product is subject to the terms and acceptance of the Northern Computers,Inc. Software Agreement. Please request a copy from Northern Computers, Inc. UL Note Section 2: System Overview Section 3: Hardware Specifications Section 5: Operation Section 6: Wiring Requirements Match case Limit results 1 per page.
Sign in here. General Access Control Discussion. Search In. Existing user? Sign in anonymously. Sign in to follow this Followers 0. Help with Honeywell NIV please Recommended Posts. Posted December 21, Thanks, Justin. Share this post Link to post Share on other sites. Hope this helps. Create an account or sign in to comment You need to be a member in order to leave a comment Create an account Sign up for a new account in our community.
Register a new account. Sign in Already have an account? Sign In Now. Sign In Sign Up.
You need to be a member in order to leave a comment. Sign up for a new account in our community. It's easy! Already have an account? Sign in here. General Access Control Discussion. Search In. Existing user? Sign in anonymously.
And a ca. Sign in to follow this Followers 1. Northern N iv run light not on. Recommended Posts. Snoddyone 0. Posted October 25, Share this post Link to post Share on other sites. Posted November 2, Posted November 3, Create an account or sign in to comment You need to be a member in order to leave a comment Create an account Sign up for a new account in our community.
Register a new account. Sign in Already have an account? Sign In Now. Power Fail 15 Red Loss of primary power with panel powered by 12 VDC battery fast flashing indicates battery charge is too low to operate panel even with primary power available. Com Loop 16 Yellow Lit indicates the out…. A communication loop with a PCI at the end of the line.
PPanel must beanel must be earearth grounded. PPanel must beanel must be earearth grou…. Initialization must include the E Option and the G designation with a number following it. The number following the G will tell the panel that groups with a number higher than this number are to be used in the split method.
If the number is EVE…. You must consult with and get approval of, local fire officials before installing locks or devices on any doors that may be fire exits. Use of egress push buttons may not be legal. Single action exit may be required. Always obtain proper permits and approvals in writing before installing equipment.
Notice: This equipment has been tested and found to comply with the limits for a Class A digit…. With auto-relock operation, an output relay controlling a door lock de-energizes when the corresponding Input Point door status switch returns to normal state, and the I…. Both poles of a given relay have a normally-closed terminal, a common terminal and a normally- open terminal.
See Figure Northern recommends using the A pole of the relays for locks inductive loads a…. Terminal Block 5 and Terminal Block 6. It supports the interface to two Wiegand output card readers and provides an alarm point common. Terminal Block 6 contains alarm input points terminals.
Any N alarm c…. LED Functions. When an LED is lit it indicates that its relay is energized, that is, the normally open relay contacts become closed and the normally closed relay contacts become open. Not lit indicates relay is de-energized, that is normally open and normally….
Enter into the terminal emulation program. The letters will echo back on the screen if the C is working properly. See the CA1 Manual for further details. Problem: A card number is not transmitted to the programming device when a card …. Anti-passback with Two and Four Card Readers. Keypads may be substituted for card readers on TB8. In anti-passback configurations with two card readers, both devices activate Output Relay 1 Door 1 upon valid code use.
With four card readers, readers 1 and 2 activate Output Relay 1 Door 1 ; reader 3 and 4 activate Output Relay 3 Door 2. In anti-passback applications requiring a separa…. See Appendix A or software operato…. Auto-relock Doors 1 and 2 without Anti-passback. Output Relay 2 de-en…. Additional Panel Features. Terminal Block 8 is used for conductor matrix keypad connections and also provides an alarm point common. Terminal Block 9 is located just to the right of Terminal Block 8.
It has the power supply and auxiliary connections. See also Input Points wiring req. Card Reader Connections to TB5. NIII Terminal Block 5 supports interface for two Wiegand output card readers and provides an alarm point common. The shi…. Auto-relock with Anti-Passback.